X822

From All for Raspberry Pi, Arduino, Lattepanda, Orange Pi, Pine64 | by Geekworm
Jump to: navigation, search


X822
X822
X822

Overview

The new member of the Raspberry Pi storage expansion board family - X822 (Dual 2.5" SATA HDD/SSD Shield ) is coming.

Features

  • Ideal storage solution for Raspberry Pi - Dual 2.5" SATA HDD/SSD Shield
  • Supports up to 4TB 2.5-inch SATA hard disk drives (HDD) / solid-state drive (SSD)
  • Supports 2 HDD or 2 SSD or HDD+SSD working at the same time
  • Supports operating system installation and booting from your HDD/SSD
  • Provides additional 2 USB ports for Raspberry Pi
  • Powers the Raspberry Pi via on-board XH2.54 connector - Only one power adapter required
  • Integrated USB 3.1 Gen1 to SATA 6Gb/s bridge controller
  • Integrated USB 3.1 Gen 1 Hub Controller
  • USB 2.0 connectivity offers plug-and-play functionality on your Raspberry Pi
  • Quick file transfer with high-speed USB3.0 5Gb/s connectivity from a PC or a Mac
  • Specially-made USB3.0 jumper to connect with Raspberry Pi - no additional cables needed
  • LED blue indicator indicates drive status
  • Fully compatible with X735 for intelligent and safe power management
  • PCB Size: 165mm x 108mm

[NOTE]

  • USB3.1 Gen 1 port, SSD sequential write speed >300MB/s
  • 2.5" SATA HDD/SSD not included
  • As with all SSDs, new media must be formatted before use
  • Performance depends on host system, workload, and SSD media used
  • SSDs use exceptionally high performance storage media that will run hot when under load
  • Older SSD drives with less efficient flash media may not perform as well as newer drives

Power supply request

Power supply: 5.1Vdc +/-5% , 4A (Require high quality power supply!!!)

Ports & Connectors:

  • USB socket - USB 3.0 type A x 3
  • DC jack - 5.5x2.5mm x 1
  • Power input / output connector - XH2.54 2-pin x 1

Installation Guide

X822 installation guide

Matching Metal Case

No matching case now

Packing List

  • 1 x X822 Board
  • 1 x USB3.0 Jumper
  • 1 x 2-Pin Power Connection Wire
  • 1 x USB 3.0 A-Male to A-Male Data cable
  • 2 x Spacer F/F 2.5x12
  • 2 x Spacer M/F 2.5x12
  • 6 x Spacer F/F 2.5x15
  • 10 x Screw M2.5x6
  • 4 x Screw M3x6

Document

Add your comment
All for Raspberry Pi, Arduino, Lattepanda, Orange Pi, Pine64 | by Geekworm welcomes all comments. If you do not want to be anonymous, register or log in. It is free.


Anonymous user #2

3 months ago
Score 0++
Could this board support using two 2.5 SATA Hard drives as RAID 1 drives allowing the Raspberry Pi to function as a server?

Admin

3 months ago
Score 0++
Hello, The X822 support 2 pcs 2.5 inch SATA hard drives, and the RAID 1 drives depends on the software not on hardware, hope to get your understanding!

Anonymous user #1

3 months ago
Score 0++
do one usb provide the data of both hdd or us1 is for hdd1 and usb2 is for usb2?

Admin

3 months ago
Score 0++

Hello sir, There is a USB HUB chip on the X822 board, so it is only need to connect one usb bridge or USB cable to provide the data of both hdd.

Hope to get your understanding!