X700
Contents
Overview
The X700 is a multifunctional expansion board for all current models of the Raspberry Pi using a 40 pin header. It provides intelligent and safe power management, safe shutdown, full poweroff through software and an advanced uninterruptible power supply. The X700 reserves the 40-pin header that can be stacked with other Raspberry Pi accessory boards for enhanced applications. The X700 can also be used with the X820 (2.5" HDD/SSD Shield), X850 (MSATA SSD shield), X822, for safe data backup.
SAFETY INSTRUCTIONS AND WARNINGS
- You must read these safety instructions and warnings before charging your batteries.
- Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the below instructions may result in fire, personal injury and damage to property if charged or used improperly.
- Never make wrong polarity connection when charging and discharging battery packs. Always double check polarity of battery's connector to make sure "+" to "+" and "-" to "-".
- Do not mix and use old batteries and new batteries, or batteries with different brand names.
- Lithium batteries has it's cycle life, please replace old battery with new one when it reaches it's service life or when it is two year old, whichever comes first.
- When charging Battery Pack, please put battery in a fire proof container. Please don't leave the X700 on the wood material or carpet and unattended.
- Must keep the X700 away from children.
Features
| Item | Description | |
| Compatible with | Raspberry Pi Model B+/ 2 Model B / 3 Model B / 3 Model B+ / 3 Model A+ | |
| Operating System | Raspbian
Stretch Safe shutdown function tested for Raspbian, other operating systems to be tested and advised |
|
| Key Features | Smart Uninterruptible Power Supply (UPS) Provides continuous operations for up to 10hours (depending on battery type used) 5.1V 3000mA Power Backup for even the most demanding Pi 3 set ups 18650 dual Cells Lithium Ion Holder Can work with single or dual 18650 Lithium Ion battery Integrated battery protection circuit Integrated over current protection and over voltage protection Integrated Maxim's fuel-gauge systems (Reading battery voltage and percentage via i2c) Intelligent automatic charging and discharging On-board 4 green LEDs indicate battery charging and discharging levels of 25%, 50% , 75% and 100% On-board red LED show the status of battery charging or fully charged Intelligent and safe power management Equipped with both momentary button and latching switch for easy power control Press the momentary button to turn on Press the momentary button and hold for 1~2seconds to reboot Press the momentary button and hold for 3~7seconds to implement safe shutdown Press the momentary button and hold for >8seconds to force shutdown Supports safe shutdown and full poweroff through software On-board switch convenient to select latching or momentary power control switches Press the latching power switch once to turn on and again to implement safe shutdown On-board LED shows the status of power on, reboot and shutdown On-board PH2.0 connectors allows to use external latching switch or momentary button Powers the Raspberry Pi via the 40-pin header - no additional cabling required Allows power input via DC jack or Micro-USB socket or XH2.54 connector Allows power output via XH2.54 socket and or the 40-pin header Other Reserved 40-pin stackable Header for Add-On Boards Powers the Raspberry Pi via the 40-pin header - no additional cabling required Works with all current models of the Raspberry Pi using a 40 pin header On-board DC jack (5.5*2.5mm) and micro-USB socket convenient for power input On-board connector allowing to connect external power switch and DIY your perfect case |
|
| Specification | Power
supply: 5.1Vdc，2.5~4A UPS output: 5.1V 3A UPS charging current: 2.5A 18650 Battery Request: battery voltage: 3.7V-4.2V and without protect circuit Recharge Threshold: 3.99V |
|
| Note | WARNING:
DO NOT APPLY POWER TO YOUR RASPBERRY PI VIA THE PI's MICRO USB SOCKET. DO NOT APPLY POWER TO X700 VIA THE X820's MICRO USB SOCKET AND DC JACK AT THE SAME TIME. DO NOT USE 18650 BATTERY WITH BUILT-IN PROTECTION CIRCUI |
Packing List
- 1 x X700 board
- 1 x Installation screw pack (Spacer F/F M2.5*20, Screw M2.5*6)
Document
X700 use the same script with X730.
We test this shell script base official Raspbian '2018-11-13-raspbian-stretch.img' version;
wget https://raw.githubusercontent.com/geekworm-com/x730-script/master/x730.sh sudo chmod +x x730.sh sudo bash x730.sh printf "%s\\n" "alias x730off='sudo x730shutdown.sh'" >> ~/.bashrc sudo reboot
Installation Guide
Enable comment auto-refresher
Anonymous user #5
Permalink |
Anonymous user #5
Anonymous user #6
Anonymous user #4
Permalink |
Anonymous user #2
Permalink |
Admin
Anonymous user #2
Permalink |
Admin
Anonymous user #3
Anonymous user #1
Permalink |
Admin