Difference between revisions of "X710"

From All for Raspberry Pi, Arduino, Lattepanda, Orange Pi, Pine64 | by Geekworm
Jump to: navigation, search
(Packing List)
Line 51: Line 51:
  
 
==Packing List==
 
==Packing List==
*X710 Power mgt Board x 1
+
*X710 Power mgt Board x 1  
*2-Pin Power Connection Wire x 1
 
 
*Screw M2.5 *5mm x 8  
 
*Screw M2.5 *5mm x 8  
 
*Spacer F/F M2.5 *12mm x 4  
 
*Spacer F/F M2.5 *12mm x 4  

Revision as of 17:05, 4 December 2019


Overview

The X710 is a power management expansion board for all current models of the Raspberry Pi using a 40-pin header. It provides 5A of continuous output current over a wide 6V to 36V operating input range with excellent load and line regulation,intelligent and safe power management, safe shutdown and full poweroff through software, and a low noise cooling fan which enables the use of the Raspberry Pi in extreme conditions including very high temperature environments. The X710 also reserves the 40-pin header that can be stacked with other Raspberry Pi accessory boards for enhanced applications.

Features

FOR USE WITH Raspberry Pi 1 Model B+/ 2 Model B / 3 Model B / 3 Model B+ / 3 Model A+ / 4 Model B
OPERATING SYSTEM - Raspbian Stretch

- Safe shutdown function tested for Raspbian, other operating systems to be tested and advised

KEY FEATURES
  • - Ideal power management solution for Raspberry Pi
  • - Integrated high-efficiency step-down DC-DC converter
  • - Wide 6V to 36V operating input range
  • - 5A continuous output current
  • - High efficiency up to 90%
  • - On-board DC jack and XH2.54 connector for power input
  • - Power output via XH2.54 connector and the 40-pin header
  • - Intelligent and safe power management
  • - Equipped with momentary button switch for easy power control
  • - Press the button to turn on
  • - Press the button and hold for 1~2seconds to reboot
  • - Press the button and hold for 3~7seconds to implement safe shutdown
  • - Press the button and hold for >8seconds to force shutdown
  • - Supports safe shutdown and full poweroff through software
  • - Integrated high-performance MOSFET power switch allows continuous drain current up to 17A
  • - On-board LED shows the status of power on, reboot and shutdown
  • - On-board PH2.0 connectors allows to use external latching switch or momentary button
  • - Powers the Raspberry Pi via the 40-pin header - no additional cabling required
  • - 30mm x 30mm low noise fan for processor cooling
  • Reserved camera slot and display cutout - Both can still be used with X710 attached
  • - Reserved 40-pin stackable Header for Add-On Boards
  • - Works with all current models of the Raspberry Pi using a 40 pin header
  • - Fully compatible with X820, X850, X860, X870, X822, X852, X825, X828, X855, X856, X857
SPECIFICATION
  • - Power supply: 6~36Vdc ≥ 2A
  • - Output: 5V 5%, Max 5A
  • - DC power jack : 5.5*2.5mm, Positive Tip
  • - Board size: 65 x 57mm
NOTES
  • - Full poweroff through software is not supported when using external latching power switch
  • - Don't connect any 5V-powered device to XH2.54 power input connector.
  • - Do not apply power to your Raspberry Pi via the Pi's Micro-USB socket or type C socket

Packing List

  • X710 Power mgt Board x 1
  • Screw M2.5 *5mm x 8
  • Spacer F/F M2.5 *12mm x 4
  • Spacer F/F M2.5 *12mm x 4

Document

For the script, please refer to Software Guide

FAQ

Add your comment
All for Raspberry Pi, Arduino, Lattepanda, Orange Pi, Pine64 | by Geekworm welcomes all comments. If you do not want to be anonymous, register or log in. It is free.