X750

From All for Raspberry Pi, Arduino, Lattepanda, Orange Pi, Pine64 | by Geekworm
Revision as of 09:06, 7 September 2019 by Admin (talk | contribs) (FAQ)
Jump to: navigation, search
X750
X750
X750
X750
X750-A1


Overview

  • The X750 is a multi-functional expansion board for all current models of the Raspberry Pi using a 40 pin header. It provides intelligent and safe power management, safe shutdown, full power off through software and an advanced uninterruptible power supply.
  • The X750 reserves the 40-pin header that can be stacked with other Raspberry Pi accessory boards for enhanced applications, and it's the high-end product of the Geekworm UPS family.
  • ​Important Note: The X750-A2 must be use with X750 18650 UPS HAT Shield, it is no use if you just purchase the X750-A2 board.

Features

ITEM DESCRIPTION
FOR USE WITH Raspberry Pi 4 Model B/3B+/3B/2B/A+/B+
OPERATING SYSTEM · Raspbian Stretch
· Safe shutdown function tested for Raspbian, other operating systems to be tested and advised
KEY FEATURES

UPS Function
· Smart and powerful Uninterruptible Power Supply (UPS)
· Provides continuous operations for up to 10~30hours (depending on battery type and qty used)
· Max 5.1V 8000mA Power Backup for even the most demanding RPi set ups
· Four 18650 Cells Lithium Ion Holder, can work with only two or three or four 18650 Lithium Ion batteries
· Can work with X750-A2 4-cell battery holder to increase battery capacity up to 38400mAh (12 18650 batteries)
· Supports 2A via micro-USB socket or 3A via DC jack fast charging
· Integrated battery protection circuit
· Integrated over current protection and over voltage protection
· Integrated Maxim's fuel-gauge systems (Reading battery voltage and percentage via i2c) - Cabling required
· Integrated 10-A fully-integrated synchronous boost converter
· Intelligent automatic charging and discharging
· On-board 4 green LEDs indicate battery charging and discharging levels of 25%, 50% , 75% and 100%
· On-board blue LED show the status of power on/off
Safe power management · Equipped with momentary button for easy power control
  Press the button to turn on
  Press the button and hold for 1~2seconds to reboot
  Press the button and hold for 3~7seconds to implement safe shutdown
 Press the button and hold for >8seconds to force shutdown
· Supports safe shutdown and full poweroff through software
· On-board blue LED shows the status of power on, reboot and shutdown
· On-board pin header to select auto power-on when power supplied or battery installed
· Ultra-low standby power consumption of μA to maximize battery life
· Operate in both charge mode and boost mode to allow full system management and battery power management
· Advanced system power path management avoids frequent charging and extend battery life
· Advanced system power path management allows 3A fast charging and powering Raspberry Pi at the same time
· Powers the Raspberry Pi via the 40-pin header - no additional cabling required
· On-board DC power jack (5.5*2.5mm) and XH2.54 connector convenient for power input
· On-board PH2.0 connector allows to connect external power switch and DIY your perfect case
· On-board XH2.54 power output connectors allow to  power other devices
· Mounting holes and standoffs provide mechanical stability of the Raspberry Pi and X750 assembly
X750-A2 · With four 18650 cells Lithium Ion holder
· Ideal solution to increase battery capacity (total battery capacity up to 38400mAh, 12 18650 batteries)
· Integrated battery protection circuit
· Mounting holes and standoffs provide mechanical stability of the Raspberry Pi, X750 and X750-A2 assembly
POWER SUPPLY · Via Micro-USB socket: 4.7~5.5Vdc, 2.5A;
· Via DC power jack: 4.7~5.5Vdc ±5%, ≥4A
· UPS output : 5.1V ±5% Max 8A
· UPS charging current: 2A via Micro-USB socket, 3A via DC jack
· Terminal Battery Voltage : 4.2V
· Recharge Threshold : 4.1V
NOTE · Power path management only enabled when applying power to the DC power jack
· Do not apply power to your Raspberry Pi via the Micro USB socket or Type-C socket.
· Do not use 18650 battery with built-in protection circuit

Packing List

  • 1 x X750 Expansion Board
  • 1 x GPIO and power daughterboard
  • 1 x 8-pin connection cable
  • 8 x Screw M2.5*5 mm
  • 2 x Spacer M/F M2.5*22+6 mm
  • 2 x Spacer F/F M2.5*22mm

X750-A2

With four 18650 cells Lithium Ion holder

  • Ideal solution to increase battery capacity (total battery capacity up to 38400mAh, 12 18650 batteries)
  • Integrated battery protection circuit
  • Mounting holes and standoffs provide mechanical stability of the Raspberry Pi, X750 and X750-A2 assembly

Packing List

  • 1 x X750-A2 Board
  • 1 x XH2.5 2Pin connector (Cable: 10cm/3.93inch)
  • 1 x Install Screws Pack

Document

We test this shell script base official Raspbian '2018-11-13-raspbian-stretch.img' version;

wget https://raw.githubusercontent.com/geekworm-com/x730-script/master/x730.sh
sudo chmod +x x730.sh
sudo bash x730.sh
printf "%s\\n" "alias x730off='sudo x730shutdown.sh'" >> ~/.bashrc
sudo reboot

FAQ

Q: 1. Will the X750-A2 stackable? Can we double or triple or more X750-A2 to hold 12/16 batteries?

A: No limit to X750-A2,you can stack mutiple X750-A2 to hold and add more batteries. But please note that the charging current is only about 2.5A, so the charging speed will be become slow if you stack mutiple X750-A2.

Q: 2. Will X750 have an auto shutdown if the battery is low?

A: Sorry no, the X750 does not support an auto shutdown if the battery is low.

Add your comment
All for Raspberry Pi, Arduino, Lattepanda, Orange Pi, Pine64 | by Geekworm welcomes all comments. If you do not want to be anonymous, register or log in. It is free.


Anonymous user #12

2 days ago
Score 0++

I think this is a problem:

Voltage: 4.23V Battery: 105%

Anonymous user #11

19 days ago
Score 0++
Your support email (support at geekworm.com) is rejecting email...

Anonymous user #11

19 days ago
Score 0++

What is the pinout for the PWR Switch?

I want to start the board from an external button; please provide details.

Anonymous user #10

22 days ago
Score 0++

What are the 5V OUT capacities? FWIW, my application needs about 1.5A at 5V for peripherals to the RPi.

I presume that the USB ports are limited to 0.5A each, but what about the XH2.54 output connectors?

Admin

3 days ago
Score 0++

Hi, All 5v output connectors are connected together and they can deliver total 8A output. Best regards,

Cindy/Geekworm

Anonymous user #9

27 days ago
Score 0++
Can you give more details on the PH2.0 4-pin External PWR Switch connector please. What is the recommend wire to use this. Where is the information and description of the function of each of the pins?

Anonymous user #9

one month ago
Score 0++
What is the pin out for the Socket mark PWR SW?

Anonymous user #8

one month ago
Score 0++
Guys, would you please advise which ports needs to be connected between X750 & X750-A2 between 2 X750-A2. The picture is taken from an angle that does not allow the lateral sockets to be identified (in/out)

Admin

one month ago
Score 0++

Hi friend,

We have updated the picture. Please refer to the 5th picture on the right of this page.

Anonymous user #7

one month ago
Score 0++
Hi, I bought a x750. What is the meaning of the jumper? Auto-On? L-SW? Please can someone explain the function to me? Thank you

Anonymous user #6

2 months ago
Score 0++
Can anyone tell me how to implement this script? do I need to mv it to bin?

Anonymous user #5

2 months ago
Score 0++
Unknowingly, I ran my x750 & pi with a poor micro USB power supply plugged into the x750 overnight following some initial testing.Now the script is showing the voltage go up to an acceptable range (3.4v), but the issue is the capacity reading from the scrip is still showing 0% capacity, and the first battery indicator light is blinking still on the board. I removed all the power (the proper charger now plugged into the dc jack and batteries) and re-installed all of them, and the problem persists . Any thoughts?

Anonymous user #4

2 months ago
Score 0++
The x750ups.py script does provide a model for monitoring battery level, assuming it is accurate. Mine shows voltage at only 4.17v with eight batteries, but that might be the protection circuit causing a low reading. The charge level is shown as 98%. There is a test in the script for battery below 20%, so similar code might be used to shutdown the device.

Anonymous user #4

2 months ago
Score 0++
I notice the output format for the “date” command is different on my systems equipped with X750 and X735 boards. Is that a side effect of the GitHub software installation?

Anonymous user #4

2 months ago
Score 0++
The date difference seems Buster related, not X750 related.

Anonymous user #4

2 months ago
Score 0++
What is the issue with using 18650 batteries with the protection circuit? (" Do not use 18650 battery with built-in protection circuit") Is it that the board has the same circuit and the batteries won't work?

Anonymous user #3

3 months ago
Score 0++
Is there a chance that a STEP model can be released for the board?

Admin

2 months ago
Score 0++
Hi, there is no plan right now, please pay attention to geekworm.com, thanks!

Anonymous user #2

3 months ago
Score 0++

installed X750 hat on raspberri pi, installed new 18650 battery's powering via usb on X750 everything seems working ok, after loading batterys to full ( all four leds green lights up) the raspberry pi shuts down, whats going wrong??

have the same problems with unprotected as with protected new battery's 18650

Anonymous user #1

5 months ago
Score 0++

Just fyi,

Confirmed with seller that this does not have a low voltage cutoff. This will throw the devices attached to a boot loop. I just hope that this has low voltage battery protection to not destroy the battery.